Home > Airhead > Engine & Drivetrain > Engine > Engine Block > Engine Block 1970-1976 Models >

Rear Main Crankshaft Seal - BMW Airhead; 11 11 1 338 342 / Elring
11 11 1 338 342,11111338342,rear main seal,R45 crankshaft seal,R50 crankshaft seal,R60 crankshaft seal,R65 crankshaft seal,R75 crankshaft seal,R80 crankshaft seal,R90 crankshaft seal,R100 crankshaft seal,R45 seal,R50 seal,R60 seal,R65 seal,R75 seal,R80 s
 
Alternative Views:
Part #: CShaft-Seal342

Crankshaft Seal for BMW Airhead (100m OD x 80mm ID x 10mm H) also known as the "Rear Main Seal"

NOTE: When applicable, replace flywheel O-Ring Part No:FW-ORing093 when replacing this main seal.
Often it is best to replace the oil pump seal OilPumpOring895
Need an installation tool? See CSSealTool342

Vehicle Manufacturer: BMW
Application: BMW Airhead Models
Make/Model: BMW R45, R50, R60, R65, R75, R80, R90, R100
Model Years: 1969 - 1996
Manufacturer #: 11 11 1 338 342

(See APPLICATION TABLE tab BELOW to verify vehicle fitment)

Brand: Made in Germany
BMW List Price $34.72
USD Price $34.72
BUY NOW $27.99

Quantity in Stock:263

Part #: CSHAFT-SEAL342
Quantity:

Description
 		Application Table
 
The seal must be preformed to the flywheel (1970-1980) or to the flywheel guide ring (1981-1995).

The seal is not pre-shaped and in some cases can be pushed on. If the shaft is not rounded or chamfered you must pre-shape the seal prior to installation - usually attained by pushing the seal into the drift to install it.

Note that the new seal is only used on the R100GS (swing arm with no oil). If this seal is used on models with swing arm (R80 - R100RT), the oil will transfer from the swing arm into the gearbox. The vent passage in the gearbox cover must be blocked on all R100GS models.

The seal is pre-shaped when fitted on the installation arbor. Use caution and ensure that the spiral on the sealing lip is not damaged. The new seal will seat in rapidly if installed dry.

See Installation Tips HERE (Courtesy - Brook Reams)

Please see BMW Service Information Document here
Removing Flywheel and Rear Main Seal (Courtesy Brook Reams)
Rear Main Seal Installation (Courtesy Brook Reams)

Related Products
Final Drive Oil Seal - BMW Airhead 1960 to 9/1984; 33 12 3 004 343, 33 12 1 233 528 / EnDuraLast Crank Shaft Bearing Shell Set - BMW Airhead; 11 24 1 258 460 / Glyco Crankshaft Rear Main Seal Tool - BMW Airhead / EnDuraLast Crankshaft Thrust Washer Red , BMW Airhead ; 11 11 1 256 973 / BMW
USD Price $15.99

Add
USD Price $79.99

Add
USD Price $72.00

Add
USD Price $53.85

Add
33 12 3 004 343,33123004343,33 12 1 233 528,33121233528,R45 final drive seal,R50 final drive seal,R60 final drive seal,R65 final drive seal,R69 final drive seal,R75 final drive seal,R80 final drive seal,R90 final drive seal,R100 final drive seal,R45 drive 11 25 1 256 477,11251256477,R45 crankshaft bearing,R50 crankshaft bearing,R60 crankshaft bearing,R65 crankshaft bearing,R75 crankshaft bearing,R80 crankshaft bearing,R90 crankshaft bearing,R100 crankshaft bearing,connecting rod 11 11 1 338 342,11111338342,rear main seal,R45 crankshaft seal,R50 crankshaft seal,R60 crankshaft seal,R65 crankshaft seal,R75 crankshaft seal,R80 crankshaft seal,R90 crankshaft seal,R100 crankshaft seal,R45 seal,R50 seal,R60 seal,R65 seal,R75 seal,R80 s 11 11 1 256 973,11111256973,R50 thrust washer,R60 thrust washer,R65 thrust washer,R75 thrust washer,R80 thrust washer,R90 thrust washer,R100 thrust washer